Permatex® 27005 Gel Squeeze™ High Strength Threadlocker RED Gel, 5 gram

PERMATEX® High Strength Threadlocker RED Gel is a high strength anaerobic threadlocking gel conveniently packaged in a new Gel Squeeze™ applicator. The product, like its liquid counterpart, is a single component, anaerobic gel that cures when confined in the absence of air between close fitting metal surfaces, ideal for all 3/8" to 1" (10 mm to 25 mm) and greater diameter threaded assemblies. Excellent chemical resistance and temperature resistance range of -65 degree Fahrenheit to +300 degree Fahrenheit (-54 degree Celsius to +149 degree Celsius). The assembly may require the use of heat to remove bolts. NSF Nonfood Components Program Listed (P1) (135870).

• OEM specified
• Gel formula provides "liquid-reliability" without drips, globs, mess or waste
• High strength threadlocker for heavy-duty applications 3/8" to 1" (10 mm to 25 mm)
• Especially well-suited for permanently locking studs and press fits
• Adds 3,000 PSI holding power on slip and press fit assemblies
• Replaces set screws and snap rings
• Locks against vibration loosening
• May require heat or special tools for removal
• Conforms to ASTM D5363 AN0221 (Mil-S-46163A, Type I, Grade K).
• Cylinder block and rocker arm studs, ring gear bolts, frame bolts, shock absorber bolts.
• Cap screws and mounting studs on differentials.
• Improved Reliability
• Eliminates vibration issues
• Seals against leakage
• Prevents rusting of threads
• Designed for use on vertical or hard-to-reach applications
• Cures without cracking or shrinking
• Adjusts or disassembles with hand tools.
• No mess Gel Twist™ or Gel Squeeze™ applicator
• Gel-type product does not drip when applied
• Single component
• No curing outside of joint
• No torque compensation required during assembly.
• Transmission shaft bolts
• Cylinder block
• Rocker arm studs
• Ring gear bolts
• Fan hub bolts
• Shock absorber bolts
• Frame brackets
• Frame bolts
• Hydraulic press studs
• Suspension fasteners
• Large studs
• Heavy equipment bolts
• Gear bolts
• Railroad assemblies
• Construction equipment.
• Clean all threads (bolt and hole) with a cleaning solvent such as Permatex® Brake and Parts Cleaner and allow to dry.
• Remove the translucent protective cap by pulling off at an angle.
• Remove cap and squeeze 1/8" to 1/4" (3 mm to 6 mm) of material beyond tip.
• Apply threadlocker to the engagement area of the male fitting (usually the leading 5 to 6 threads).
• Assemble parts and tighten to recommended torque.
• If unused gel contacts metal threads, do not retract threadlocker back into the tube. Wipe off with a clean towel.
• Replace protective cap.
• Residual liquid films and/or fillets outside the joint are readily soluble in Permatex® Brake and Parts Cleaner.
• Cured product can be removed with a combination of soaking in Permatex® Gasket Remover and mechanical abrasion such as a wire brush.
• Apply localized heat to nut or bolt to approximately 500 degree Fahrenheit (260 degree Celsius). Disassemble while hot.
• Remove loose product from nut and bolt following cleanup procedure above.
• Apply Surface Prep™ activator to all threads, regardless of metal type and allow to dry.
• Apply threadlocker gel as above.
• Assemble and tighten as usual.
• Viscosity @ 25 degree Celsius, cP
• Brookfield RVF, spindle #3, @ 20 RPM: Gel
• Flash Point (TCC), degree Fahrenheit (degree Celsius): >200 (>93)

Shipping calculated at checkout. Usually ships within 24 hours.

We ship within the contiguous United States.

Returns accepted within 30 days by mail. Return shipping is paid by the customer. See our refund policy.